
ServicesMetal Roofing
Metal Roofing in Beech Grove
We install standing seam and exposed-fastener metal roofs on homes that need a long-term answer. Before any panel goes up, we check the deck, the attic airflow and the flashing details, so the new roof doesn't inherit the problem that ruined the old one.
When a metal roof is the right fix
Metal roofing is steel or aluminum panels in place of asphalt shingles. We install two main types. Standing seam panels hide their fasteners under raised seams. Exposed-fastener panels use screws with rubber washers driven through the face of the metal. Each sheds water, snow and hail differently than shingles do.
Before we recommend metal, we find out why your current roof is failing. If shingles are curling because the attic runs hot and damp, a metal roof over that same poor ventilation will collect condensation on its underside and drip into the insulation. If the leak traces back to a cracked pipe boot, roof repair may be all you need. We tell you the cause first, then talk about panels.
Metal makes the most sense when you plan to stay in your home a long time, when low-pitch sections keep leaking under shingles, or when Central Indiana freeze-thaw cycles keep forcing ice under the shingle edges at the eaves. Financing is available if the upfront cost is what's holding you back.
What goes into a new metal roof
Stripping to bare plywood
Every layer of old roofing comes off so the decking is fully exposed, and we walk each sheet to test it underfoot. Soft or delaminating plywood gets replaced before anything else goes down, since screws and clips set into rotted wood work loose with time.
Heat-rated synthetic underlayment
In direct sun, metal panels get hotter than asphalt, so the underlayment beneath them has to be rated for that temperature. Valleys, eaves and every pipe or vent opening also get ice and water membrane.
Floating clip attachment
Steel grows and shrinks a measurable amount from a cold winter night to a hot summer afternoon. On standing seam roofs, sliding clips hold each panel while letting it move. Without them, fasteners pop, seams strain and the panels start to look wavy.
Trim, flashing and pipe boots
That means ridge caps, rake and eave trim, valley flashing, and boots designed to seal against metal. At chimneys, counterflashing is cut into a mortar joint rather than relying on a sealant bead that cracks after a few seasons.
Attic airflow fixes
Soffit intake and ridge exhaust are sized to work together, so damp attic air exits rather than condensing on the cool underside of the steel.
Snow guards at the right spots
Snow tends to slide off metal all at once. Guards placed above doorways, walks and lower roof sections hold it back so it melts off in smaller amounts.
Signs metal roofing may be the right call
You're facing another shingle replacement
If this is your second or third tear-off, a metal roof can break that cycle. We'll compare it honestly against shingle roofing for your situation.
Low-slope sections leak every winter
Porch roofs and shed dormers with shallow pitch hold water and ice longer than shingles tolerate. Mechanically seamed panels are rated for lower pitches than shingles allow.
Shingles keep blowing off
Repeated wind losses usually point to brittle, aging shingles or poor nailing. Interlocked metal panels resist uplift far better once properly attached.
Screws backing out on an existing metal roof
On exposed-fastener roofs, rubber washers dry out and crack, and screws loosen as panels move. Look for rust streaks or drips along screw lines. We can reseat or replace fasteners, or tell you when new panels make more sense.
Rust at cut edges or laps
Rust that starts at panel ends or overlaps means water is sitting where the coating was cut or scratched. Caught early, it can be treated and resealed.
How a metal roofing job runs
- 1
Free inspection to find the cause
We check the roof surface, the flashing details and the attic. You get photos of what we found and a plain explanation of what is really causing the trouble.
- 2
Line-item estimate and panel selection
Your written estimate spells out panel profile, steel gauge, finish and color on separate lines, and any decking or ventilation work is listed on its own. We handle the permit as well.
- 3
Tear-off in stages, sealed daily
Tarps go over plants and beds first. We strip only as much roof as we can cover with underlayment before quitting for the day, so no part of your home sits open overnight.
- 4
Panels, cleanup and walkthrough
Once panels and flashing are installed, magnets sweep the lawn and driveway for loose screws and metal slivers. Then we go over the finished roof with you before packing up.
What moves the price of a metal roof
Metal costs more upfront than asphalt, and two metal quotes for the same house can land far apart. We itemize every part of the job on your written estimate, so each charge has a name next to it. The biggest drivers are below.
- Panel system
- Standing seam with hidden clips takes more material and labor than exposed-fastener panels, but it has no screws through the face that need attention later.
- Gauge and finish
- Thicker steel resists dents better. A PVDF paint finish holds its color longer than a standard polyester finish and costs more.
- Roof shape
- Every valley, hip, dormer and skylight means custom-cut panels and extra flashing. A simple gable goes up faster than a cut-up roof.
- Deck condition and layers
- Multiple shingle layers add tear-off time and disposal. Any rotted decking found underneath is replaced at a per-sheet cost written into the estimate.
Metal roofing questions
Something not covered here? (317) 779-3204
Is a metal roof louder when it rains?
Over a solid deck with underlayment and attic insulation, rain sounds close to what you hear under shingles. The loud tin-roof noise comes from barns where panels sit on open framing with nothing underneath.
Can metal go right over my existing shingles?
It is sometimes allowed, but we usually advise a full tear-off. Going over shingles hides the deck, so we can't find rot or the source of an old leak. Trapped moisture between layers can also shorten the life of the new roof.
How does metal handle hail?
Steel panels rarely puncture, but large hail can leave cosmetic dents. Thicker gauges and textured finishes hide them better. If a storm has already hit, our storm damage repair page explains how we work with homeowners and insurance companies on claims.
What is oil canning?
It's a visible waviness in the flat part of a panel. It comes from uneven decking, over-tightened fasteners or panels that can't move with temperature. We reduce it with a flat deck, proper clips and panels with stiffening ribs.
Do you offer financing for a metal roof?
Yes, financing is available. Mention it when you call to set up your free roof inspection and we'll go over it with your estimate.

Find out if metal fits your roof
We'll check the deck, the attic and the pitch, then tell you plainly whether metal is worth it for your home or whether a repair solves the problem.